Homebuilders

Turnbuckle Safetying-Double Wrap Spiral Method

Wed, 18 Nov 2009 05:00:00 -0800

Brian Carpenter of Rainbow Aviation Services teaches us the Double Wrap Spiral method for safetying a turnbuckle.

P Lead Fabrication

Tue, 17 Nov 2009 10:23:31 -0800

Brian Carpenter of Rainbow Aviation Services demonstrates how fabricate a P Lead for a magneto.

Ducting: Scat, Sceet, Cat & Ceet

Thu, 12 Nov 2009 05:00:00 -0800

In this week's segment, Richard Koehler talks you thru the various types of ducting used on your aircraft. "Dick" is a Technical Counselor for Chapter 186, A&P aircraft mechanic with Inspection Authorization (IA), and SportAir Workshop instructor.

Aeroquip 816 Hose Fitting Installation

Thu, 05 Nov 2009 05:00:00 -0800

Brian Carpenter of Rainbow Aviation Services demonstrates how to install an Aeroquip 816 hose fitting.

Tires and Tubes

Thu, 29 Oct 2009 07:40:29 -0700

In this week's segment, Richard Koehler walks you thru the basics of tires and tubes. "Dick" is a Technical Counselor for Chapter 186, A&P aircraft mechanic with Inspection Authorization (IA), and SportAir Workshop instructor.

Rivnut Removal

Thu, 22 Oct 2009 07:43:11 -0700

Brian Carpenter of Rainbow Aviation Services discusses the removal of Rivnuts.

Firesleeve-Installation & Removal

Tue, 20 Oct 2009 07:44:57 -0700

In this segment, Brian Carpenter of Rainbow Aviation Services demonstrates the installation and removal of firesleeve.

Rivnut Installation

Thu, 15 Oct 2009 09:33:37 -0700

In this segment, Brian Carpenter of Rainbow Aviation Services discusses the more common pull rivets encountered in aviation.

Preparing a Rotationally Molded Tank for Installation

Thu, 08 Oct 2009 05:00:00 -0700

In this segment, John Monnett shows how to prepare a rotationally molded tank for installation. John Monnett is the founder of Sonex Aircraft, is an aircraft designer & builder and is an inductee in the EAA Homebuilders Hall of Fame.

Installing a Nut in a Hard to Reach Place

Thu, 03 Sep 2009 10:19:56 -0700

Getting a nut onto a bolt can sometimes be a big challenge. In this segment, Jack Dueck shows how he has solved the problem. Jack is a Technical Counselor, Sportair Workshop Instructor and member of both the EAA Homebuilt Aircraft Council and Canad

Bolt Installation

Thu, 20 Aug 2009 05:00:00 -0700

In this segment, Jack Dueck discusses the preferred way to install bolts on an aircraft. Jack is a Technical Counselor, Sportair Workshop Instructor and member of both the EAA Homebuilt Aircraft Council and Canadian Council.

AeroVee Ignition Timing

Mon, 17 Aug 2009 12:26:22 -0700

In this segment, Jeremy Monnett of Sonex Aircraft, demonstrates how to properly set the timing on the AeroVee 2.1 VW based engine conversion. Sonex Aircraft offers the AeroVee Engine which is a complete VW conversion engine kit.

Drilling Titanium

Thu, 06 Aug 2009 05:00:00 -0700

Drilling titanium sounds like it would be quite difficult but in this video Kerry Fores shows how easy it can be. Kerry built an AirVenture award winning Sonex and works at Sonex Aircraft providing technical assistance.

Torque Seal Application

Thu, 23 Jul 2009 05:00:00 -0700

Torque seal provides visual evidence that a fastner has not loosened or rotated. In this segement, Douglas Drees discusses the proper application of torque seal. Doug is a Technical Counselor and A&P mechanic from Olympia, WA.

AN Hardware Basics

Thu, 16 Jul 2009 11:42:42 -0700

In this segment, Sam Coates goes over the basics of AN bolt installation. Sam is a Technical Counselor for Chapter 1270 from the Upper Peninsula of MI.

Valve Adjustment

Fri, 15 May 2009 05:00:00 -0700

In this segment, Jeremy Monnett of Sonex Aircraft, demonstrates the proper technique to adjust the valves on a VW based engine conversion. Sonex Aircraft offers the AeroVee Engine which is a complete VW conversion engine kit.

Cutting and Fitting a Sonex Canopy

Thu, 23 Apr 2009 05:00:00 -0700

In this segment, John Monnett shows the basic steps of cutting and fitting a canopy on a Sonex. John Monnett is the founder of Sonex Aircraft, is an aircraft designer & builder and is an inductee in the EAA Homebuilders Hall of Fame.

Drilling Holes in Plexiglas

Thu, 16 Apr 2009 05:00:00 -0700

In this segment, John Monnett shares how to modify a drill bit to drill Plexiglas without cracking. John Monnett is the founder of Sonex Aircraft, is an aircraft designer & builder and is an inductee in the EAA Homebuilders Hall of Fame.

Cutting Instrument Holes with a Hole Saw

Tue, 14 Apr 2009 12:09:55 -0700

In this segment, Earl Luce demonstrates a great technique to make cutting accurate and perfectly aligned instrument panels holes. Earl is an EAA SportAir Workshop instructor and offers plans for the Wittman Buttercup.

Motor Mount Fabrication

Thu, 12 Mar 2009 10:44:51 -0700

The complex geometry of a motor mount makes scratch building a challenging task. Earl Luce shows how to make a simple jig that will greatly simply the task. Earl is an EAA SportAir Workshop instructor and offers plans for the Wittman Buttercup.

File Safety-Making a File Handle

Thu, 26 Mar 2009 05:00:00 -0700

In this hint, Charlie Becker shares some cheap and easy ways of making sure your files have handles. Charlie is on staff at EAA and is currently building a Sonex.

CherryMAX Rivet-Installation/Removal

Thu, 26 Feb 2009 11:14:29 -0800

In this segment, Brian Carpenter of Rainbow Aviation Services demonstrates how to install and remove a CherryMAX rivet. Brian is an A&P aircraft mechanic with an Inspection Authorization rating (IA), a DAR for light sport and amateur built, a Sport

Cutting Tubing with your Table Saw

Wed, 11 Feb 2009 13:35:59 -0800

Earl Luce demonstrates the correct and safe way to cut steel tubing with a table saw.

Oetiker "Ear" Clamp Installation/Removal

Thu, 12 Feb 2009 05:00:00 -0800

If you're working on a Rotax engine, odds are you'll be faced with either installing and removing an "Oetiker" clamp. In this episode, Brian Carpenter of Rainbow Aviation Serivces shows you the technique.

Oil Filter Removal, Inspection and Installation

Thu, 22 Jan 2009 05:00:00 -0800

In this Hint, Brian Carpenter of Rainbow Aviation Services demonstrates how to remove and inspect an oil filter. Brian is an A&P aircraft mechanic with an Inspection Authorization rating (IA).

Nicopress Fittings - Fabrication

Tue, 20 Jan 2009 08:28:05 -0800

Joe Norris demonstrates the proper way to fabricate a nicopress fitting. Joe is EAA's Homebuilders Community Manager, and has built or restored several aircraft.

Aeroquip Hose End Fabrication & Removal

Thu, 01 Jan 2009 05:00:00 -0800

In this segment, Brian Carpenter of Rainbow Aviation Services demonstrates how fabricate an Aeroquip hose end.

Measuring Tips

Tue, 23 Dec 2008 06:00:00 -0800

This week, Ken Terrio shares some tips on measuring, and making templates for angles. Ken is a member of Chapter 166 and has built a Pober Jr Ace.

Flared Tubing-Fabrication & Assembly

Thu, 18 Dec 2008 05:00:00 -0800

In this Hint, Brian Carpenter demonstrates how to fabricate and assemble flared tubing for use in many aircraft installaitons. Brian is an A&P aircraft mechanic with an Inspection Authorization rating (IA).

Metal Propeller Repair

Thu, 04 Dec 2008 05:00:00 -0800

In this segment, Brian Carpenter of Rainbow Aviation Services demonstrates how to make a minor repair to a metal propeller. Brian is an A&P aircraft mechanic with an Inspection Authorization rating (IA).

Installing a Nut in Hard to Reach Places

Wed, 26 Nov 2008 05:00:00 -0800

When you assembling your aircraft, you will run into place where it seems virtually impossible to be able to a nut onto a bolt. Mark Forss, anEAA staff member and SportAir Workshop instructor, shows a few techniques that might solve this problem.

Masking Tape of Any Width

Thu, 20 Nov 2008 05:00:00 -0800

Ken's second tip is a quick and easy way to make a piece of tape any width you need. Ken is a member of Chapter 166 and has built a Pober Jr Ace.

Wing Attach Fittings-Installation

Thu, 20 Nov 2008 05:00:00 -0800

This week, Ken Terrio of Chapter 166 shares how to locate wing attach straps on an aircraft. This can be a challenge as the plans usually call for a measurement out in space.

Composite Propeller Repair

Thu, 13 Nov 2008 09:03:49 -0800

In this segment, Brian Carpenter of Rainbow Aviation Services demonstrates how to make a minor repair to a carbon fiber propeller. Brian is an EAA Technical Counselor and Flight Advisor.

Wally Anderson's Strategy for Completing Your Aircraft

Thu, 16 Oct 2008 05:00:00 -0700

Wally Anderson has completed three RV aircraft. In this episode, he shares some tips on how to complete that project. Wally is a Technical Counselor and member of EAA's Homebuilt Aircraft Council.

Safetying Fasteners

Thu, 02 Oct 2008 05:00:00 -0700

In this week's edition, Joe Norris of the EAA Staff demonstrates the twist method of safetywiring castelled nuts.

Drilling in Tight Places

Thu, 18 Sep 2008 05:00:00 -0700

Sometimes you simply can't get a drill into place to drill a hole. In this episode, Charlie Becker of the EAA staff shows some ways to drill in tight places.

Safetying-Cotter pins

Thu, 11 Sep 2008 05:00:00 -0700

In this week's edition, Joe Norris of the EAA Staff demonstrates the standard and alternate way to properly install cotter pins.

Torque Wrench Technique

Thu, 04 Sep 2008 05:00:00 -0700

Torque Wrench Technique

Torque Wrench Basics

Thu, 07 Aug 2008 05:00:00 -0700

Torque wrenches are absolutely necessary when building your own aircraft. In this video Jeremy Monnett of Sonex Aircraft discusses the two styles available and how they work.

Propeller Field Repair

Thu, 24 Jul 2008 05:00:00 -0700

Believe it or not, "super" glue and baking soda can often be used to make a field repair to a nicked propeller. In this video, Timm Bogenhagen of the EAA staff shows the technique that is used extensively in the ultralight and light plane world.

Properly Attaching a Rod End Bearing

Thu, 19 Jun 2008 14:18:55 -0700

In this video, Jack Dueck shows the proper way to attach a rod end bearing to a control lever. Jack is a Technical Counselor, Sportair Workshop Instructor and member of both the EAA Homebuilt Aircraft Council and Canadian Council.

Bolt Nomenclature

Wed, 11 Jun 2008 05:00:00 -0700

Bolt Nomenclature

Turnbuckle Safetying

Thu, 05 Jun 2008 09:13:12 -0700

Turnbuckle Safetying

Nuts, Bolts & Washers in Hard to Reach Places

Wed, 26 Nov 2008 06:00:00 -0800

Nuts, Bolts & Washers in Hard to Reach Places

Jig for Drilling Tubing

Thu, 08 May 2008 08:38:58 -0700

Jig for Drilling Tubing

Installing Nut Plates

Wed, 30 Apr 2008 10:56:27 -0700

Installing Nut Plates

Non-Slip Zip Ties

Thu, 24 Apr 2008 05:00:00 -0700

Non-Slip Zip Ties

Drilling Piano Hinges

Wed, 19 Mar 2008 11:00:00 -0700

Drilling Piano Hinges

Tie Wrap Stand Off

Thu, 03 Apr 2008 12:34:06 -0700

Nylon tie wraps are commonly used on ULs & lightplanes to secure wires, fuel line and other non-structural parts. Nylon tie wraps degrade over time when exposed to heat and UV light so owners should plan to replace these on a routine basis.

Make Your Own Deburring Tool

Wed, 16 Sep 2009 09:46:45 -0700

In this segment, Jim Martin shows how to construct a deburring tool from an old knife sharpener Jim is a AirVenture Workshop instructor from Chapter 93 in Madison WI.

Bending Aluminium Across the Grain

Thu, 24 Sep 2009 05:00:00 -0700

In this segment, Jack Dueck explains the best way to bend aluminum in consideration of the grain. Jack is a Technical Counselor, Sportair Workshop Instructor and member of both the EAA Homebuilt Aircraft Council and Canadian Council.

Bending Aluminum Plate with an Arbor Press

Thu, 17 Sep 2009 05:00:00 -0700

In this segment, Kerry Fores shows how to use an arbor press to bend sheet metal. Kerry built an AirVenture award winning Sonex and works at Sonex Aircraft providing technical assistance.

Closing Aluminum Angle

Thu, 27 Aug 2009 10:52:49 -0700

Kerry Fores shows two ways to bend aluminum angle. Kerry built an AirVenture award-winning Sonex and works at Sonex Aircraft, providing technical assistance.

Cutting Aluminum on a Bandsaw

Thu, 02 Jul 2009 05:00:00 -0700

In this segment, Sam James shares a couple of tips for cutting aluminum on a bandsaw. Sam is the owner of James Aircraft.

Removing Plastic Coating from Sheet Metal

Thu, 25 Jun 2009 05:00:00 -0700

Doug Kelly demonstrates how to use a soldering iron to remove the plastic coating in just the area that must be riveted. Doug is a Technical Counselor for Chapter 524 in Frederick, MD and a member of the EAA Homebuilt Aircraft Council.

Polishing Sheet Metal

Thu, 04 Jun 2009 05:00:00 -0700

Kerry Fores from Sonex gives builders a detailed look at the ins and outs of polishing sheet metal.

Sheet Metal Tools 101

Thu, 28 May 2009 05:00:00 -0700

Rivets 101

Thu, 30 Apr 2009 05:00:00 -0700

In this segment, Jack Dueck covers the basics of driven rivets. Jack is a Technical Counselor, Sportair Workshop Instructor and member of both the EAA Homebuilt Aircraft Council and Canadian Council.

Edge Roller

Thu, 09 Apr 2009 05:00:00 -0700

In this Hint, Wally Anderson shows how to use an edge roller to improve the finish of your riveted sheet metal skins. Wally is a Technical Counselor and member of EAA's Homebuilt Aircraft Council.

Blind Rivet Identification

Thu, 12 Mar 2009 05:00:00 -0700

In this segment, Brian Carpenter of Rainbow Aviation Services discusses the more common pull rivets encountered in aviation.

Indirect Riveting Technique

Thu, 08 Jan 2009 05:00:00 -0800

In this Hint, Wally Anderson shows how to drive a rivet in hard to reach places like ailerons and flaps. Wally is a Technical Counselor and member of EAA's Homebuilt Aircraft Council.

Dimpling in hard to reach places

Thu, 11 Dec 2008 05:00:00 -0800

In an earlier Hint, we showed the "simple dimple die". In this episode Wally Anderson demonstrates another special tool that can be used to dimple sheet metal in hard to reach places.

Routing Sheet Metal Parts

Thu, 06 Nov 2008 05:00:00 -0800

In this weeks tip, Mark Forss shows how to use a router to mass produce sheet metal parts. Mark is an EAA staff member and SportAir Workshop Instructor.

Blue Lining a rib for installation

Thu, 23 Oct 2008 06:16:14 -0700

The use of a "blue line" mark makes installation of a sheet metal rib very easy. In this vdieo, Kerry Fores of Sonex Aircraft shows you this handy technique.

Strap Duplicator

Thu, 09 Oct 2008 05:00:00 -0700

There will be times when you need to duplicate a hole in sheet metal. In this episode, Mark Forss of EAA shows how a strap duplicator can solve the problem.

Sheet metal rib from scratch-Part 6-Fluting

Thu, 09 Oct 2008 05:00:00 -0700

Making a Sheet Metal Rib from scratch (part 6). Kerry Fores shows you how fluting the rib flanges will straighten out a rib. Kerry Fores works at Sonex Aircraft providing technical assistance.

Sheet metal rib from scratch-Part 5-Flanging

Thu, 02 Oct 2008 05:00:00 -0700

Making a Sheet Metal Rib from scratch (part 5). Kerry Fores shows you how to flange a lightening hole. Kerry Fores works at Sonex Aircraft providing technical assistance.

Riveting with a C Frame

Thu, 25 Sep 2008 05:00:00 -0700

Perfect rivets while blindfolded? Believe it or not, with a special adapter for a C Frame you can get perfect driven rivets every time. In this episode, Wally Anderson demonstrates how easy the technique.

Sheet metal rib from scratch-Part 4-Form Blocks

Thu, 25 Sep 2008 05:00:00 -0700

Making a Sheet Metal Rib from scratch (part 4). Kerry Fores shows you how to form the flanges of a rib using form blocks. Kerry Fores works at Sonex Aircraft providing technical assistance.

Sheet metal rib from scratch-Part 3-Lightening Holes

Thu, 18 Sep 2008 05:00:00 -0700

Making a Sheet Metal Rib from scratch (part 3). Kerry Fores demonstrates how to use a fly cutter to make lightening holes. Kerry Fores works at Sonex Aircraft providing technical assistance.

Sheet metal rib from scratch-Part 2-Cutting

Thu, 11 Sep 2008 05:00:00 -0700

Making a Sheet Metal Rib from scratch (part 2). Kerry Fores walks you thru how to cut out your blank using the Malco snips. Kerry Fores works at Sonex Aircraft providing technical assistance.

Sheet metal rib from scratch - part 1 of 6

Thu, 04 Sep 2008 05:00:00 -0700

Making a Sheet Metal Rib from scratch (part 1). Kerry Fores walks you thru how to lay out your blank using the "magic washer" trick. Kerry Fores works at Sonex Aircraft providing technical assistance.

Bending Aluminum Angle with a Wrench

Thu, 21 Aug 2008 05:00:00 -0700

Sometimes you will need to change the bend on a piece of extruded aluminum angle. In this video, Jeremy Monnett of Sonex Aircraft shows how this can be done with a large adjustable wrench.

Filing Aluminum

Thu, 17 Jul 2008 05:00:00 -0700

A vixen file is ideal for rapid removal of aluminum, brass, copper and hard rubber. In this video, Jason Monnett of Sonex Aircraft demonstrates using a vixen file to clean up a piece of aluminum cut on a bandsaw.

Drilling out a Driven Rivet

Thu, 10 Jul 2008 08:02:26 -0700

Drilling out a Driven Rivet

Cutting Inside Holes

Thu, 26 Jun 2008 05:00:00 -0700

Jack Dueck shows how a step drill, hole saw, fly cutter and nibbler can be used. Jack is a Technical Counselor, Sportair Workshop Instructor and member of both the EAA Homebuilt Aircraft Council and Canadian Council.

Cutting Aluminum Using a Bandsaw

Wed, 11 Jun 2008 05:00:00 -0700

Cutting Aluminum Using a Bandsaw

Backriveting

Thu, 05 Jun 2008 09:16:21 -0700

Backriveting

Paper Template

Thu, 29 May 2008 14:46:03 -0700

Paper Template

Flush Riveting

Thu, 29 May 2008 14:40:44 -0700

Flush Riveting

Deburring Metal

Fri, 06 Jun 2008 11:39:51 -0700

Deburring Metal

Drilling Sheet Metal

Thu, 15 May 2008 05:00:00 -0700

Drilling Sheet Metal

Basic Layout Using a Rivet Fan

Thu, 08 May 2008 08:49:35 -0700

Basic Layout Using a Rivet Fan

Simple Dimple Die

Fri, 02 May 2008 15:18:27 -0700

Simple Dimple Die

Microstop Countersink Basics

Thu, 10 Apr 2008 05:00:00 -0700

Microstop Countersink Basics

Drilling Out a Rivet

Wed, 26 Mar 2008 11:58:20 -0700

Drilling Out a Rivet

Cleco 101

Wed, 12 Mar 2008 11:20:19 -0700

Cleco 101

Pull Riveting in Tight Places

Tue, 26 Feb 2008 07:04:22 -0800

Pull Riveting in Tight Places

Stringer Installation

Tue, 21 Jul 2009 13:32:33 -0700

In this video, Michael Hoye shows how to get the stringers just where you want them. Michael is a member of Chapter 168 in Dallas, Texas.

Gas Welding Tank Safety

Thu, 09 Jul 2009 05:00:00 -0700

It is critical that a gas welding rig be set up properly to ensure a safe work environment. In this video, Dave Conrad discusses how to make sure your welding tanks are leak free. Dave is a Technical Counselor for Chapter 640 in Wausau, WI.

Laminated Pull Block as Drill Guide

Wed, 10 Jun 2009 14:58:02 -0700

Laminated Pull Block as Drill Guide

Forming Fabric Around a Tight Radius

Thu, 11 Jun 2009 05:00:00 -0700

You may think it is difficult to form fabric around a tight curve, but in this segment Carah Durell shows you how easy it can be done with the proper technique. Carah is a an EAA member and former Chapter 1 Young Eagle that works for Poly-Fiber.

Ribstiching-Finish Knot

Thu, 21 May 2009 05:00:00 -0700

The final rib stitching knot you need to know is the finish knot. In this video, Carah Durell shows you how to wrap up your rib stitching. Carah is a former Chapter 1 Young Eagle that works for Poly-Fiber.

Ribstiching-Seine Knot

Thu, 14 May 2009 05:00:00 -0700

One of the more challenging aspects of fabric covering an aircraft is learning to tie the Seine know. In this episode, Carah Durell shows you the proper procedure. Carah is a former Chapter 1 Young Eagle that works for Poly-Fiber.

Ribstiching-Starter Knot

Thu, 07 May 2009 05:00:00 -0700

In this episode, Carah Durell shows you the proper procedure for tying the starter knot when rib stitching. Carah is a former Chapter 1 Young Eagle that works for Poly-Fiber.

Iron Calibration

Thu, 19 Feb 2009 05:00:00 -0800

Before you can start covering your aircraft, you'll need to make sure the your iron is properly calibrated. In this episode, Carah Durell of Poly-Fiber shows you the proper procedure.

U Brackets Made Easy

Thu, 16 Oct 2008 05:00:00 -0700

U brackets for wing fittings, rudders, etc. have to be spot on. This can be a real challenge but in this episode Earl Luce shows you an easy way to accomplish the task. Earl is an EAA SportAir Workshop instructor and a volunteer EAA Technical Couns

Fishmouthing Tubing with an Angle Grinder

Thu, 28 Aug 2008 05:00:00 -0700

In an earlier video, Earl Luce demonstrated how to fishmouth tubing with aviation snips. In this video, Earl shows how a couple of angle grinders can make fishmouthing tubing an easy job

Simple Welding Jig

Thu, 14 Aug 2008 05:00:00 -0700

Why spend a lot of time building an elaborate jig if it for a simple, one off part? In this weeks video, Earl Luce demonstrates how to keep it simple. Earl is an EAA SportAir Workshop instructor and a volunteer EAA Technical Counselor.

Fishmouthing Tubing with Aviation Snips

Wed, 12 Mar 2008 11:24:41 -0700

Fishmouthing Tubing with Aviation Snips

Bending Tubing

Wed, 05 Mar 2008 11:13:10 -0800

Bending Tubing

Removing Staples after Gluing

Thu, 03 Jul 2008 05:00:00 -0700

Staples are used routinely to hold wood components in place until the glue dries. In this video, Timm Bogehagen of the EAA staff shows a couple of techniques to easily remove the staples once the glue is dry.

Bending Wood Capstrips

Wed, 30 Apr 2008 09:04:15 -0700

Bending Wood Capstrips

Glueing Gussets Using T-88

Thu, 17 Apr 2008 05:00:00 -0700

Mixing T-88 and Glueing Gussets

Routing Plywood Ribs & Noseblocks

Fri, 04 Apr 2008 08:16:38 -0700

Routing Plywood Ribs & Noseblocks

Building a Wood Wing Rib Jig

Tue, 26 Feb 2008 07:03:46 -0800

Building a Wood Wing Rib Jig

Composite Layup with Peel Ply

Thu, 13 Aug 2009 05:00:00 -0700

In this segment, Dave Saylor demonstrates a composite layup using peel ply. Dave is an A&P aircraft mechanic with Inspection Authorization (IA), and owner of Aircrafters LLC in Watsonville, CA.

Composite Fairings Made Easy

Thu, 30 Oct 2008 05:00:00 -0700

Almost evey project requires making some special composite fairings. In this episode Wally Anderson demonstrates how to fabricate a quick and easy composite fairing. Wally is a Technical Counselor and member of EAA's Homebuilt Aircraft Council.

BNC Connectors for Antennas

Thu, 10 Sep 2009 08:49:00 -0700

In this week's segment, Dick Koehler demonstrates how to fabricate a BNC Connector. Dick is a Technical Counselor for Chapter 186, A&P aircraft mechanic with Inspection Authorization (IA), and SportAir Workshop instructor.

How to Solder

Thu, 18 Jun 2009 06:32:17 -0700

Richard Koehler walks you through the basics of soldering. Dick is a Technical Counselor for Chapter 186, an A&P aircraft mechanic with Inspection Authorization (IA), and a SportAir Workshop instructor.

Relays

Thu, 02 Apr 2009 05:00:00 -0700

In this segment, Kas Osterbuhr discusses relays and demonstrates how they work. Kas is an EAA SportAir Workshop instructor for the Electrical Systems, Wiring and Avionics workshop.

Molex Pin Connectors

Thu, 19 Mar 2009 05:00:00 -0700

In this segment, Kas Osterbuhr shows how to crimp Molex type pins and how to load them into the connector body. Kas is an EAA SportAir Workshop instructor for the Electrical Systems, Wiring and Avionics workshop.

Stripping Mil-Spec Wire

Wed, 04 Mar 2009 12:54:09 -0800

Stripping wire seems simple enough but there is a correct way to do it. In this epidsode Kas Osterbuhr demonstrates how to strip mil-spec wire. Kas is an EAA SportAir Workshop instructor for the Electrical Systems, Wiring and Avionics workshop.

Identifying Mil-Spec Wire

Wed, 04 Mar 2009 12:56:52 -0800

This week Kas Osterbuhr explains how to read MilSpec wire. Kas is an EAA SportAir Workshop instructor for the Electrical Systems, Wiring and Avionics workshop.

Tools for Electrical Wiring

Thu, 29 Jan 2009 11:13:03 -0800

In this hint, Kas Osterbuhr starts us down the path of wiring your aircraft by going over the more common tools you'll need to wire an aircraft. Kas is an EAA SportAir Workshop instructor for the Electrical Systems, Wiring and Avionics workshop.